Look, I don't have a magic buying formula. After 11 years of handling bulk elevator components and metal siding orders for a mid-size construction supply operation, I have something less exciting: a checklist. I've also made and documented nine significant procurement mistakes, totaling roughly $48,000 in wasted budget and several avoidable delays. This article is the part I wish someone had shown me in 2017.
There is no one right strategy
Most buying advice tends to preach one idea: use a direct manufacturer, always get three quotes, never buy from the cheapest source. Those rules are fine if your project is simple. Most construction projects aren't. The right process depends on the situation. The sooner you identify which situation you are in, the cheaper your mistakes become.
In my work, the same set of questions comes up again and again. Do you need the part for a safety-certified elevator system? Is the metal panel part of a visible exterior or tenant-facing facade? Is the product going to be hidden inside a wall or mechanical room? Each answer changes what it's safe to buy and how much verification you need.
Here are the three scenarios I now use.
Scenario A: Bulk elevator components for a building that is already running
If a component is going into a hoistway, it is not just a spare part. It becomes part of a certified system. It might physically fit, but that doesn't mean it is electrically, logically, or legally compatible with the elevator system already on site. I made this mistake early in my career because I treated elevator parts like shelf stock.
One spreadsheet told me a supplier was 18% cheaper on a 60-piece order of bulk elevator components. My gut said their response times were a preview of their overall quality. I went with the numbers. The supplier had cross-referenced the parts against a legacy thyssenkrupp elevator catalog. The physical size was right, but the control interface wasn't compatible with the current firmware on the jobsite. We caught the mismatch before installation, but not before spending $3,700 on return freight and replacement logistics.
What changed after the thyssenkrupp elevator division merger makes this even more important. When thyssenkrupp's elevator division became TK Elevator, old part numbers and current part numbers started floating around at the same time. Some suppliers update their catalogs faster than others. That means a current order may still be quoted under a legacy thyssenkrupp part number, and that part number might have been superseded twice already.
- Ask the supplier to list both the current manufacturer part number and any legacy thyssenkrupp part number on the quotation.
- If they say it fits a thyssenkrupp elevator, ask which revision, firmware family, and serial prefix range they tested against.
- Request the written compatibility document or OEM reference before you release the order.
- For bulk elevator components, never hide the end use. Suppliers need to know if the material goes into an occupied building.
Scenario B: Visible metal siding that customers will judge
This is where I have the least empathy for purchasing rules that ignore appearance. If the siding is visible from a street, lobby, or tenant entrance, it is more than a weather barrier. It is the business card of everyone who specified it and installed it. From the outside, buying colored metal siding looks like matching a paint swatch. The reality is that most field issues happen before the first panel is installed: wrong coil lot, missing coating documentation, reverse side finished incorrectly, or gauge downgraded without a structural review.
People assume the lowest quote means the steel supplier is more efficient. What they don't see is how many hidden coordination costs show up later.
A good metal siding distributor is your pre-install quality control. I'm not saying they need to be the most expensive distributor in town. But they do need to understand the difference between an interior liner panel and an exterior system with wind load requirements.
A practical metal siding specification guide I wish I had in 2017
- Confirm the substrate gauge and alloy. If the original drawing says 22 gauge, don't accept a 24 gauge substitute without a structural review. The price difference is small compared with a wall that ripples.
- If the color is part of the design, specify a PVDF coating with at least 70% resin content. The word PVDF alone is not enough.
- Decide whether the reverse side is visible. In my first year, I ordered 1,200 linear feet of exterior metal wall panel with coating only on the outside face. The reverse became visible at an entrance soffit, and the bare primer line looked unfinished. That mistake cost about $7,200 in touch-up and a two-week delay.
- Get the coil or slitting lot number before shipment. Mixed coils from the same color code can show a subtle but visible sheen difference once the sun hits the facade.
- If the spec says domestic steel, treat that as a claim that needs proof. Per FTC advertising guidelines (ftc.gov), material origin claims should be truthful and substantiated. Ask for a mill certificate.
The extra care pays off in the finished project. On a recent tower entrance renovation, the building manager told me that the new panels were the first ones they had not needed to shield from glare or touch up after installation. That kind of feedback is why I keep a quality-first bias when the product is visible.
Scenario C: Utility-grade metal panels and hidden replacement parts
Here's the twist. As much as I believe visible quality matters, I also believe in spending your money where the job actually sees it. If a metal panel goes into a mechanical room ceiling or a back-of-house equipment screen, a premium architectural finish is wasted. That's not an excuse to buy junk; it's a reason to buy utility-grade material with a clear spec.
This scenario matters because over-specification is its own form of waste. A project that pays for a high-end architectural finish behind a wall is stealing budget from the entrance that clients actually see.
- Weigh price against total installed cost. A painted panel that scratches during install costs more labor to patch than a coil-coated one costs in material.
- Buy standard 20-foot lengths when they ship by truck, and ask for proper dunnage. Broken corner panels are waste no matter how cheap the unit price was.
- Don't buy a product with premium branding if there is no code, owner, or durability requirement behind it.
How to tell which scenario you are in
If you are doing an elevator modernization or repair, use Scenario A for anything connected to a controller, brake, door system, or safety circuit. If you are ordering siding for an exterior facade or a visible interior wall, use Scenario B. If the material will be enclosed, non-visible, and not connected to a safety system, Scenario C applies.
Still unsure? Ask two questions.
Question 1: Does failure of this product create a safety or code issue? If yes, treat it like Scenario A, no matter what the marketing material says.
Question 2: Will the owner, tenant, or inspector make a judgment about the project by looking at this product? If yes, treat it like Scenario B.
If you answered no to both, use Scenario C and buy to a sensible, documented standard.
The point isn't to have one magic answer. The point is to stop buying everything with the same brain. I still maintain a written pre-ordering checklist, and it starts with three words: where does this go? Answer that question first, and the thyssenkrupp elevator component and metal siding decisions start to sort themselves out.