Structural steel and elevator engineering article hero

Engineering article

The Cheapest Elevator Components We Bought Ended Up Costing Us $5,400

· Emilia Novak

I'll say it plainly: if you're sourcing elevator components, cable railing, or handrail systems by comparing unit prices, you're not saving money. You're deferring it.

I'm a procurement manager for a mid-sized construction firm. I've managed a budget of roughly $180,000 a year for the past six years, tracked every invoice, and built our cost tracking system from scratch. That includes hundreds of orders for elevator components, steel fixtures, and railing systems.

The cheapest vendor we've ever used ended up costing us 470% more than we "saved." That's not hyperbole. That's a spreadsheet cell.

The Order That Broke My Spreadsheet

The wake-up call came in March 2023. We were building a three-story commercial atrium and needed a cable railing manufacturer to supply around 400 linear feet of railing. Three quotes came in. I want to say the lowest was about 32% below the next one—don't quote me on the exact number, but it was the largest gap I'd seen in three years of running this process.

I almost approved it on the spot. (Should mention: our procurement policy requires three quotes minimum. This experience is why I wrote that policy.)

The low bidder's quote didn't include stamped engineering drawings, compliance testing for the handrail load requirements, delivery as a single batch, or anything resembling a warranty beyond "one year." I went with them anyway. That was the mistake.

Three months later, the code inspector flagged the top rail. The profile didn't meet the graspable surface requirement. According to the ADA Standards (access-board.gov), Section 505.5 specifies a circular cross-section with an outside diameter of 1.25" to 2" for handrail gripping surfaces, and the vendor's product was outside that range. When I asked for compliance documentation, they sent a generic spec sheet stamped "FOR REFERENCE ONLY." No testing reports. No engineering calculations. Zero traceability.

The rework cost us $6,800—actually, $6,834 when I add the extra freight for replacement fittings. The "savings" on the original quote? $1,400. That's a $5,400 swing, against us. The cheap railing wasn't cheap. It was expensive with extra steps.

What TCO Actually Includes

Since that project, I've used a total cost of ownership (TCO) framework for every component order. If a vendor can't or won't speak to each of these items, the quote is incomplete:

  • Total landed cost. Freight, customs, staging, and the coordination cost of partial deliveries. A cable railing manufacturer that ships the full order in one batch is often cheaper than one that sends pieces over six weeks—even when the freight line item looks higher.
  • Compliance cost. Who pays for stamped calculations, load testing, and inspection support? For handrail systems, this is where most projects go sideways.
  • Risk cost. Your schedule. Your labor. The other trades waiting on site while a rework happens. When elevator components arrive and don't fit, the mechanic's clock keeps running.
  • Rework cost. Nobody quotes this. It's also the one that hurts most.

Here's something vendors won't tell you: the first quote is almost never the real price for a project that needs compliance support. Engineering review, test reports, site visits—that's where the margin lives. That doesn't make the vendor dishonest. It means a quote comparison that ignores those costs is fiction.

Handrail Systems Compliance: The Line Item Nobody Sees

Most buyers focus on material—stainless steel grade, cable gauge, post spacing—and completely miss the code requirements. The question everyone asks is, "What's the tensile strength of the cable?" The question they should be asking is, "Can you prove this railing meets the building code in our jurisdiction?"

The International Building Code, for example, requires handrails and guards to resist a 200-pound concentrated load applied at any point along the top rail. Local amendments vary. A railing that passes in one jurisdiction can fail in another—and it's still exactly the same product.

The difference between a compliant and non-compliant handrail is rarely visible in the photos. It's in the paperwork. A supplier that provides stamped calculations, test evidence, and traceable documentation isn't adding cost—they're buying down your risk. When you multiply that risk across 400 linear feet of railing, the "cheap" price starts looking a lot less attractive.

Elevator Components: Why "OEM" Is a Budget Word

The same logic applies to elevator components, but the stakes are higher. A thyssenkrupp elevator isn't a commodity; it's a system. The buttons, fixtures, and controllers are engineered as a system—not as standalone parts that happen to share the same machine room.

In Q2 2024, we sourced replacement fixtures for a modernization project. One vendor offered aftermarket buttons at less than half the price of the OEM equivalent from thyssenkrupp. The cost controller in me felt a pull. I'll admit it.

Then I ran the TCO. The OEM parts came with guaranteed compatibility with the existing controller, documentation that satisfied the inspector, a warranty that actually pays out, and the manufacturer's own liability backing. The aftermarket parts came with a "compatibility chart" the seller typed up themselves.

Actual copy from the vendor's email: "should work fine, we haven't had returns."

That's not a specification. That's a hope.

Here's the question I ask now, and I wish I'd asked in March 2023: what does the cheap part cost when the inspection fails, the system goes down, or the building owner calls the integrator for a fix that's no longer covered? When you're replacing thyssenkrupp elevator buttons in a system regulated under ASME A17.1—the elevator safety code—"should work fine" doesn't appear anywhere in the compliance pathway.

"But My Budget Caps at X"

I hear the objection, because I've made it myself: "This is all great, but my budget caps at X. I can't stretch the numbers to a higher quote."

Budgets are real. But here's what six years of data taught me: budget overruns don't come from the parts you deliberately overpay for. They come from the things you "saved" on, in unpredictable categories—rework, schedule slippage, expedited freight, reinspection fees. When I audited our 2023 spending, I found that under-priced sourcing decisions accounted for over a third of our project cost overruns.

We didn't fix it by demanding lower quotes. We fixed it by requiring a TCO worksheet on any order above a set threshold. First-year result: project overruns down 22%. The "cheap" purchases didn't go away. The unauthorized risk did.

If a vendor can't explain why their quote is dramatically lower than the market rate, that's not a gift. That's a clue. And if your budget is too tight to absorb rework, the last thing you should do is buy the part most likely to need it.

The Bottom Line

The cheapest quote is the most expensive thing we've ever bought. Six years of spreadsheets say the same thing: price is what you pay at the beginning. Cost is what you pay by the end. The goal isn't the lowest price. It's the lowest total cost.

When you're procuring thyssenkrupp elevator components, choosing a cable railing manufacturer, or reviewing handrail systems compliance requirements, you're not buying a part. You're buying the absence of problems. That costs more up front—and it costs far less by the time the inspector leaves and the doors open.

I'll take that trade every time. Done.

Share WhatsApp
Emilia Novak
Emilia Novak

Emilia Novak is a flooring and architectural-surfaces analyst covering ceramic and porcelain tile, natural stone, resilient flooring, underlayments, countertops, adhesives, grout, and installation accessories. She uses ASTM C373 and ASTM C648 test evidence while comparing water absorption, breaking strength, slab flatness, substrate moisture, joint width, slip resistance, and installed tolerances. Her specification guides help architects, contractors, and buyers match surface systems to traffic, wet-area exposure, maintenance demands, and substrate conditions.

Latest from the blog